Please ensure the following:
• Your Snuza Pico is on
• Your Snuza Pico is in range
• If your smart device is running on Android 6.0 or above, ensure your Location service is enabled.
– Open Android Settings and tap on the “Connections” item.
– Scroll down to “Location” and tap on it.
– Ensure it is enabled/activated by turning it on.
– Go back to Connections and locate the “Bluetooth” item. Tap on it and make sure it is turned on.
– Restart the Snuza Connect App. You should now be able to connect to your Snuza Pico.
• Your Bluetooth Technology is activated on your smart device
• You are logged onto the App.
• You are trying to connect to your registered Snuza Pico.
• If none of the above work, please contact us.
Bluetooth Technology only allows one smart device to connect to the Snuza Pico at a time.
Reset your Snuza Pico by holding the power button for 10 seconds and then release. After the green light has stopped flashing try to turn it ON again. If this did not fix the problem please contact Customer Care by completing the form on the contact us page.
A Snuza Pico can only be registered to one username. If you bought your Snuza Pico second hand please contact the previous owner of the Snuza Pico and request that they deactivate the Snuza Pico by logging in with their username at connect.snuza.com and clicking on the red de-activate button at the bottom of the page.
Yes, please visit connect.snuza.com and invite them as a secondary user.
Smart device minimum requirements::
• Bluetooth 4.0
• Apple devices:
• iOS 8.0 or later
• Android devices:
• Android 4.4 or later
Reset the Snuza Pico by holding the power button for 10 seconds and then release. After the green light has stopped flashing, try to turn it on again.
When you first put the Snuza Pico on, it is slightly colder than your baby and tends to reduce the temperature of the skin around the Pico. The Snuza Pico needs at least 10 to 15 minutes to reach the same temperature as the child for accurate temperature readings.
Click on this link to reset.
Is your Snuza Pico software up to date? You can check what firmware version your Snuza Pico is by going to the settings screen of the Pico in question on the Snuza Connect App on your smartphone. On Android, look under the Snuza Pico serial number to see the version number. On iOS, click on the ‘i’ in the top right corner of the screen and look for “Firmware version”.
If the battery is still charged and you have not disabled your remote ON/OFF function, you should be able to connect to your Snuza Pico within range. Once connected, switch your Snuza Pico ON and the breathing alarm will sound after 20 seconds.
Ensure that the thin flap of the diaper is folded over the thicker part, which is what the Clip grips on to. Refer to the following video for how to attach your Snuza Pico.
Reset the device by holding the power button for 10 seconds and then release. After the green light has stopped flashing try to turn it on again. If this did not fix the problem ontact Customer Care by completing the form on the contact us page.
If the purple light is flashing then your device is in pause mode, please ensure that the clip lever is closed correctly and it is not paused via the app.
Remove the top Clip Lever by opening it past the 60 degrees open position. Take the lower Clip and insert the right pin in holding the Clip at a 90 degree angle to the Snuza Pico with the teeth side facing inwards, then pull the left side firmly until the other pin can clip into position. The Clip Lever and Clip on the Snuza Pico have been designed to be removable to make it easy to clean the unit. To use your Snuza Pico, please ensure that both Clips are fitted properly.
If your Wall Adapter complies with the following output specifications: 5V, >200mA then you can use it. If not then please go to your local retail store and purchase a Wall Adapter that is compatible.
The Charging Case needs the lid when closed, to apply pressure to the Snuza Pico and enable charging. Try to reattach the lid. If you cannot, then you can still charge your Snuza Pico by placing it onto the Charging Cradle and applying light downwards pressure to the Snuza Pico until the Snuza Pico displays charging mode.
Please ensure that the USB connector is properly inserted into the Charging Case and that the Wall Adapter is plugged in and switched ON.
To re-seat the clip, please watch the following video.
The clip is designed to be replaceable and will unseat if moved more than 60 degrees past the opened position. There is a friction stop at 60 degrees, but with a little force, it can be moved beyond this.
Go to connect.snuza.com and click on Forgot Password; enter your username/email and you will be prompted to click on the registration option if you have not done so yet.
Download our easy-to-use product manuals for up to date information on how to use your Snuza baby monitor.