戻る

Frequently Asked Questions for Snuza Go!SE

My Snuza Go battery was dead when purchased.

Switch the Snuza Go OFF. Remove the battery for 10 seconds and do not press any buttons while the battery is out. Place the battery back in the Snuza GoDo not switch the Snuza Go ON. Does the Snuza Go start alarming with the Battery Indicator Light flashing red? If yes, then If the Snuza Go is still under the twelve month guarantee contact Customer Care by completing the form on the contact us page.

My Snuza Go!SE beeps continuously. What do I do?

Replace the battery if the Snuza Go!SE has been used extensively for a long period of time. If the battery has recently been replaced contact a Snuza Representative if the Go!SE is still under the 12 month guarantee.

Contact Customer Care by completing the form on the contact us page.

Which replacement battery does my Snuza Go!SE use?

If you would like to purchase a battery for the Snuza Go! with the letters SE next to the name (Go!SE), the substitute battery that can be purchased is the Primary-cell Energizer CR2 or Primary-cell Duracell CR2. No re-chargeable batteries to be used. 


If you have an older model, the Snuza Go! (Non-SE) model, you can use a SAFT LS14250 3.6V Lithium Thionyl Chloride 1/2 AA battery. No re-chargeable batteries to be used.

These can be purchased at most battery or camera retailers. Please purchase reputable brand batteries only.

Does the Snuza Go!SE need to touch my baby's skin?

No, your Snuza Go!SE does not need to directly touch your baby's skin.




Your Snuza monitor can be clipped onto the folded waistband of the diaper or elasticated pants, as long as the Movement Sensor touches your baby in their tummy area. Your baby may also wear a thin layer of clothing (Eg. a vest) between the Movement Sensor and the skin, but you'll need to ensure that the Movement sensor maintains contact. The Go!SE can also be used if your baby is dressed in light clothing (Eg. A Babygro) over the nappy or pants.


Please keep in mind that too much clothing may muffle the alarm, which needs to be heard clearly if your little one is covered with clothing or blankets.




If you have any questions, please contact support@snuza.com.

Why is the audible tick on my Snuza Go!SE switching itself on?

The Audible tick feature was activated. The Audible tick can be activated or deactivated by pressing the 'MODE/OFF' button. Refer to your user manual under 'Settings' on the Audible tick for more information and usage.

Can the alarm period be changed on the Snuza Go!SE monitor?

Yes, it can be adusted to the preferred alarm period setting of 15, 18 or 20 seconds. Refer to the Snuza Go!SE user manual under 'Alarm activation period' for instructions on how to set the alarm period.

How do I switch my Snuza Go!SE off?

To switch the monitor off, press the 'ON/OFF' and 'MODE/OFF' buttons simultaneously. A shutdown tone will be heard.

Why is my Snuza Go!SE is completely dead, even with a new battery?

If the Snuza Go!SE is still under the 12 month guarantee contact Customer Care by completing the form on the contact us page.

My Snuza Go!SE no longer makes any noise or alarms. What do I do?

Remove the battery and press the 'ON/OFF' button while the battery is out. Place the battery back into the Snuza Go!SE. Do not switch the unit 'ON'. Does the Snuza Go!SE start alarming with the battery light flashing red? If yes, Replace the battery if the Snuza Go!SE has been used extensively for a long period of time. If the battery has recently been replaced contact a Representative if the Go!SE is still under the 12 month guarantee.

Contact Customer Care by completing the form on the contact us page.

Why won't my Snuza Go!SE vibrate?

The Snuza Go!SE model does not have a Vibration feature. Only the Snuza HeroSE, HeroMD and Snuza Pico 2 has the vibration feature.

My Snuza Go!SE movement light flashes red and it beeps (like a low battery alert, but I have replaced the battery recently). What do I do?

When your Snuza Go!SE flashes red and you can hear the audible alarm, you need to immediately check on your baby. This alert is activated when no breathing movement has been detected for the selected time period (15, 18 or 20 seconds).

My Snuza Go!SE is switching itself back on. What do I do?

To turn the Snuza Go!SE 'OFF' press both the 'ON/OFF' and 'MODE/OFF' buttons simultaneous. A shut down tone will be heard. Ensure that the Snuza Go!SE is 'OFF' after usage.

My Snuza Go!SE is draining batteries. What do I do?

After usage make sure that the Snuza Go!SE is switched OFF. An audible tone will be made on shutdown. Not switching the monitor OFF will drain the battery. Please refer to your manual for more information.

My Snuza Go!SE is not detecting movement. What do I do?

Any damage to the sensor would cause the device not to function correctly. The guarantee does not cover the battery, incorrect application, tampering, misuse or transport damage.

Refer to the 12 month guarantee in the user manual for more information.

Why doesn't my Go!SE connect to the Snuza Connect app?

The Snuza Go!SE is not designed to connect to an app. Only the Snuza Pico 2 has the ability to connect to the Snuza Connect app and has additional features compared to the Snuza Go!SE.

The Snuza Go!SE was designed to monitor your baby's breathing movements, by clipping onto your baby's diaper or elasticised pants. If no breathing movement is detected after 15 seconds, an audible alarm will sound to alert you/caregivers to respond quickly and intervene. The alarm settings can be adjusted to 15, 18 or 20 seconds. 

If you have any questions please contact support@snuza.com

Manuals for Snuza Go!SE

Download our easy-to-use product manuals for up to date information on how to use your Snuza baby monitor.
 

English | French | German | Spanish | Dutch
English | French | Spanish
Simplified Chinese

Enquire about Snuza Go!SE

X
X

メールアドレス: